|Place of Origin:||ShenZhen|
|Minimum Order Quantity:||1|
|Packaging Details:||each packed into OPP bag ,then packed into Carton box.|
|Delivery Time:||2-5 working days|
|Payment Terms:||Paypal, TT|
CE Watercool Esc Motor Controller,
Esc Motor Controller Mosfet 120V,
120V 500A RC Boat ESC
120V 500A Watercool Speed Controller ESC With 154120 Motor For RC Boat
|Voltage||Current||Size(mm)||weight(g)||BEC (Volts/Amps)||Box Programming support||Computer Programming support||Firmware update|
l The Max Volatge is 120V.
l Two way communication while connecting it with computer.
l Motor wire can be checked while Connecting the power battery.
l Simply set function value by Prog-Box or by PC via USB link wire.
l Li-MH/Li-Po,Ne-Cd/Ne-mH,LiFe battery can be use.
l Enables setting the voltage per cell for the point at which the controller’s cut off circuitry engages.Li-MH/Li-Po from 2.0-3.6V,Ne-Cd/Ne-.4-1.0V,LiFe from2.2-2.8V
l Reverse function. the delay time of reverse is adjustable.
l Automatically detection the throttle route or can be set a fixed number by manual operation.
l Auto cut off the power within 3 seconds if no radio signs.
Timing setting may be adjusted (0°-30°) to suit the motor type.
Function value setting by transmitter
You can set some simple function values via the transmitter, but want to set the more
function values, you have to use prog-box or PC via USB link wire.
This ESC has two different types of main mode, one is Forward-Only mode(Reverse Off),
and another is Forward&Reverse mode(Reverse On). If Reverse Off mode is set, the motor
will spin forward only. And if Reverse On mode is set, the motor can spin forward and
Function value can be changed follow the step below:
1. Move the stick of the transmitter on full throttle position, power on the receiver.
2. After power on the ESC, you can hear “♪♪♪” melody; this indicates that the motor
connection is ok.
3. Don’t move the stick and wait about 5 seconds, a four-tone melody can be heard; this
indicates that a main mode programming sequence is ready.
4.And then you will hear 5 groups “♪ (a short beep)”, then 5 groups “♪♪”, then 5 groups
“♪♪♪” and then 5 groups“♪♪♪♪” ; and 5 groups “♪”,5 groups “♪-(a long
beep)♪”,5 groups “♪♪”. And these sounds of groups will circulate
5.Each group of 5 sounds stands for a different mode of ESC respectively.
6.You can put the throttle stick to the middle position during one group of 5 sounds, and
then the corresponding mode is saved.
7.Hear 1“♪”(Forward mode) or "♪♪" (Forward/Reverse mode), then you can exit the
setting mode after saving the mode.
(When the mode is saved, you can disconnect the ESC to the battery pack)
◎Forward-Only mode and Forward-Reverse mode:
After “♪♪♪” melody, Hear the “♪♪♪♪”,put the throttle stick to the middle position,
the mode is changed from Forward-Only mode into Forward&Reverse mode. If you want to
change it back, please repeat the above procedures, and vice versa.
Setting function value:
1. Reverse: On/Off.
3. Frequency: 8KHz, 16 KHz, 32 KHz.
4. Acceleration: Soft / Medium / Hard.
5. Accumulator type:NiCd/NiMh,Li-Ion/Li-Pol,LiFe.
6. NiCd/NiMH CUTOFF:×0.05,0.4V,0.5V,0.6V,0.7V,0.8V,0.9V,1.0V.×0.05 means the cut off voltage is 5% the voltage while connecting.
7. Number of cells:Auto,2S,3S,4S,5S,6S,7S,8S,9S,10S,11S,12S,16S.
8. LiIo/Pol CUTOFF:2.0V,2.1V,2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V,2.9V,3.0V,3.1V,3.2V,3.3V,3.4V,3.5V,3.6V.
9. LiFe cutoff:2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V
10. Cut Off Type::Slow down,Hard. l
11. Power limited forward: Off, 75%, 50%, 25%.
12. Power limited reverse: Off, 75%, 50%, 25%.
13. Delay time when direction convert: 0.25S, 0.5S, 0.75S, 1S, 1.5S, 2S, 3S, 5S.
14. Reverse point:Auto,fixed 1.0mS,fixed 1.1mS,fixed 1.2mS,fixed 1.3mS.
15. Forward point:Auto,fixed 1.7mS,fixed 1.8mS,fixed 1.9mS,fixed 2.0mS.
16. Throttle curve: Logarithmical,Linear,Exponential.
17. Rotation direction: Left, Right.
18. Timing monitor (TIMING MONTITOR): ON, Off.
Note:the red mark is the factory default value,you can setting function value by youself.
MAX POWER: 22000W-25000W
MAX AMP: 300A
ESC: 350 -450A
MAX VOLT: 70v / 100v
NO LOAD CURRENT::(15V) 7A
RESISTANCE Mohm): 160
SIZE: 120 x 100 ( without shaft )
WEIGHT (kg): 3.835
SHAFT: 12mm Accessory pack: Yes
Inside hall sensored ball
Internal PCB with 120 degree hall effect sensors
1.Payment :T/T ,Paypal,West union .
2.Production lead time :5 days for 100-200 pcs ,10days for 200-300pcs .
3.Sample can be delivered within 3 days.
4.Discounts are offered based on order quantities .
5.MOQ: 2 pcs.
1. Items will be shipped within 3 business day after payment completed received.
2. Items are shipped from DHL Express ,UPS ,EMS,, reach most of the countries within 3-7 days respectively.
3. Warranty Period is 2 yrs for this item.
4. If product can not work, or find it as defects within in 7 days after receipt, please contact us, we will replace or refund.
5. All emails will be answered within 1 working day.
Contact Person: Cathy