Flier HV 16S 100A RC Ebike ESC Brushless Controller Battery Powered

Flier HV 16S 100A Ebike ESC brushless controller for RC Ebike

 

 

 

Basic information:

 

 

Voltage	Current	Size(mm)	weight(g)	BEC (Volts/Amps)	Box Programming support	Computer Programming support	Firmware update
4-67V	100A	103*57*40	230g	OPTO	Yes	Yes	Yes

 

 

ESC info:

 

1:There are three pins wires for the receiver port, length is 300mm:
---The brown wire is ground,
---The yellow wire is pulse signal wire, it is a 5V PWM pulse signal and you just controll the ESC via the wire,
---The red wire is the power wire 5V input to the ESC; you must supply a 5V voltage to the red wire otherwise the ESC won't work.

 

2:A standard receiver signal is 1-2mS@50Hz. It is saild that the receiver will send 1-2mS 5V pulse per 20mS to the ESC. 1mS pulse will arm the ESC,and the motor will stop. when increase the throttle, the pulse width also increase, about 1.1mS, the motor will start to spin, and 2mS, the motor will spin at full speed.

 

3:Baterry wire: length 180mm, 10AWG. Red wire connect to the positive pole, black connect to the negative pole. The black side of the small black 18AWG line is Anti-spark wire,It is built in a bullet connector and a 10 ohms resistor. You must connect the end of the wire to the battery negative. you can connect the red wire of ESC to the positive pole of battery at first. Then connect the anti-spark wires well. The last step is to connect the black wire of ESC to the battery’s negative pole. If do so, no spark will be generated, and this will protect the main bullets connector from spark damage.

 

4.Motor wire; 3 pcs balck wire, 10AWG, 180mm.

 

5.Program wire: 4 pins, length 100mm. Use USB link to program via PC or program via program box.

 

 

 

Feature:

 

The unmanned electromechanical adjustment has a total of five lines. 3 at one end, 2 at the other end, 3 with the motor connected to 3 lines, no matter whether it is positive or negative.

 

As long as the direction of rotation is reversed, any two wires can be exchanged. The other two are power cords, which are directly connected to the battery. Forgot to have a thin servo plug, this is directly connected to the flight controller or receiver.

 

Reverse function. the delay time of reverse is adjustable.

 

The power of the motor forward/ reverse can be set.

 

Automatically detection the throttle route or can be set a fixed number by manual operation.

 

Auto cut off the power within 3 seconds if no radio signs.

 

Timing setting may be adjusted (0°-30°) to suit the motor type.

 

 

Setting function value:

 

 

1. Reverse: On/Off.

2. Timing:0°,1°,2°,3°,4°……30°.

3. Frequency: 8KHz, 16 KHz, 32 KHz.

4. Acceleration: Soft / Medium / Hard.

5. Accumulator type:NiCd/NiMh,Li-Ion/Li-Pol,LiFe.

6. NiCd/NiMH CUTOFF:×0.05,0.4V,0.5V,0.6V,0.7V,0.8V,0.9V,1.0V.×0.05 means the cut off voltage is 5% the voltage while connecting.

7. Number of cells:Auto,2S,3S,4S,5S,6S,7S,8S,9S,10S,11S,12S,16S.

8. LiIo/Pol CUTOFF:2.0V,2.1V,2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V,2.9V,3.0V,3.1V,3.2V,3.3V,3.4V,3.5V,3.6V.

9. LiFe cutoff:2.2V,2.3V,2.4V,2.5V,2.6V,2.7V,2.8V

10. Cut Off Type::Slow down,Hard. l

11. Power limited forward: Off, 75%, 50%, 25%.

12. Power limited reverse: Off, 75%, 50%, 25%.

13. Delay time when direction convert: 0.25S, 0.5S, 0.75S, 1S, 1.5S, 2S, 3S, 5S.

14. Reverse point:Auto,fixed 1.0mS,fixed 1.1mS,fixed 1.2mS,fixed 1.3mS.

15. Forward point:Auto,fixed 1.7mS,fixed 1.8mS,fixed 1.9mS,fixed 2.0mS.

16. Throttle curve: Logarithmical,Linear,Exponential.

17. Rotation direction: Left, Right.

18. Timing monitor (TIMING MONTITOR): ON, Off.

Note:the red mark is the factory default value,you can setting function value by youself.

 

 

 

Trade Terms:

 

1.Payment :T/T ,Paypal,West union .

 

2.Production lead time :5 days for 100-200 pcs ,10days for 200-300pcs .

 

3.Sample can be delivered within 3 days.

 

4.Discounts are offered based on order quantities .

 

5.MOQ: 2 pcs.

 

 

Shipping&Return:

 

1. Items will be shipped within 3 business day after payment completed received.

 

2. Items are shipped from DHL Express ,UPS ,EMS,, reach most of the countries within 3-7 days respectively.

 

3. Warranty Period is 2 yrs for this item.

 

4. If product can not work, or find it as defects within in 7 days after receipt, please contact us, we will replace or refund.

5. All emails will be answered within 1 working day.